Removable bollard storage bases: 90mm and 140mm

Short answer: A storage base (also called a storage holder) is a bolt-down steel fitting that parks a removed bollard (SW-SL90 $25 ex GST, $27.50 inc; SW-SL140 $35 ex GST, $38.50 inc; in stock). It is not an in-ground sleeve: the in-ground socket comes with each removable bollard.

Prices and stock as at October 2026. Updated 28 October 2026.

A bolt-down floor fitting that gives a removable bollard somewhere safe to stand once it's lifted out of the ground. No leaning it against a wall, no scratches, no bollard going missing.

Looking for the in-ground socket? It's included with every removable bollard.

Sizes
102mm and 152mm internal diameter
Fixing
Bolt-down base plate; not an in-ground socket
Price, ex GST
$25 (90mm), $35 (140mm); $27.50 and $38.50 inc GST
Stock
In stock in Melbourne
90mm bollard storage holder bolted to a concrete path

How it works

What a storage holder actually is

A bollard storage base (also called a storage holder) is a bolt-down carbon steel holder for a removable bollard. It's an accessory, not the bollard's ground fixing. The in-ground socket that the bollard locks into is part of the bollard itself and comes supplied with it.

The holder mounts flat to a floor surface with a bolted base plate, somewhere out of the way, along a wall inside a garage or factory door, or right beside the bollard's ground position. When you unlock a bollard and lift it out to let vehicles or machinery through, you drop it straight into the holder. It stands upright and secure until you're ready to lift it back out and lock it into the ground socket again. For the full lift-out routine, see how removable bollards work.

Terms

Storage base vs sleeve vs socket: what's the difference?

  • Socket. A steel tube set in the ground that holds the bollard in use. It is supplied with each removable bollard (SW-RB90 socket Ø102 × 4 × 225mm; SW-RB140 socket Ø152 × 4mm).
  • Storage base (storage holder). A steel fitting that bolts to the floor through four bolt holes, so the removed bollard stands upright out of the way. This is the SW-SL90 and SW-SL140.
  • Sleeve. A trade word used for either of the above, which is why we spell out which one we mean. The URL of this page still says “sleeves” for that reason.

More detail in our guide to bollard sleeve vs socket vs storage holder and the bollard terms glossary. If you need the in-ground part, see the removable bollards: the socket comes with each one.

Empty bollard storage holder bolted to concrete

Buying guide

Which holder, how many, and where to mount it

Three decisions: the size, the quantity and the spot on the floor. Get them right and the removed bollard goes back into the holder every time, instead of being left lying around.

  • Match the holder to the bollard. A 90mm bollard takes the 90mm holder (SW-SL90, 102mm internal diameter). A 140mm bollard takes the 140mm holder (SW-SL140, 152mm internal diameter). The two sizes are not interchangeable, so order the holder for the bollard you have.
  • One holder per bollard that comes out at the same time. If four bollards are lifted out for a delivery, you need four holders to park them. If only one is ever out at a time, one holder of the right size does the job. Count the bollards removed together, not the number of sockets on site.
  • Mount it on sound concrete, clear of traffic. Fix the base plate to a solid slab beside the opening or along a wall, away from vehicle paths and walkways. A bolted steel holder in a wheel path or a walkway is a trip and impact hazard.
  • Put it near where the bollard is used. If the holder is across the yard, the bollard ends up leaning on the nearest wall. A holder right beside the opening gets used every time.
  • Fixings are not included. Supply masonry anchors suited to your slab and fix them through the base plate holes.

Pulling bollards at a roller door? Our roller door bollards guide covers where they go. Tell us how many bollards come out at once and in which sizes, and we will quote the matching holders.

Both sizes

Specifications & pricing

In stock now. Tell us your quantity: bulk and pallet pricing is better.

90mm bollard storage holder bolted to a concrete path In stock

Bollard Storage Holder 90mm

SW-SL90 · Storage base for 90mm removable bollard

$25 per unit, ex GST & freight ($27.50 inc GST)

  • Internal diameter102mm
  • Wall thickness4mm
  • Heightapprox. 225mm
  • Base plate150 × 105 × 5mm (4 bolt holes)
  • MountingSurface bolt-down
  • MaterialCarbon steel
  • Matching bollardRemovable bollard 90mm

Need 20 or more, or a mixed order? Ask for a volume price.

140mm bollard storage holder bolted to a concrete path In stock

Bollard Storage Holder 140mm

SW-SL140 · Storage base for 140mm removable bollard

$35 per unit, ex GST & freight ($38.50 inc GST)

  • Internal diameter152mm
  • Wall thickness4mm
  • Heightapprox. 200mm
  • Base plate155 × 205 × 5mm (4 bolt holes)
  • MountingSurface bolt-down
  • MaterialCarbon steel
  • Matching bollardRemovable bollard 140mm

Need 20 or more, or a mixed order? Ask for a volume price.

Prices as at October 2026, per unit, ex GST ($27.50 and $38.50 inc GST) and freight. Final pricing is confirmed on your written quote. Buying in volume? See trade and bulk supply. Based in Melbourne: bollards in Melbourne.

Specifications at a glance

Specifications of the SW-SL90 and SW-SL140 bollard storage bases side by side
SpecificationSW-SL90SW-SL140
Suits90mm removable bollard140mm removable bollard
Internal diameterØ102mmØ152mm
Wall thickness4mm4mm
Heightapprox. 225mmapprox. 200mm
Base plate150 × 105 × 5mm155 × 205 × 5mm
Bolt holes44
Price, ex GST (inc GST)$25 ($27.50)$35 ($38.50)
StockIn stockIn stock
Is it an in-ground socket?No, a bolt-down floor fittingNo, a bolt-down floor fitting

In the price

  • The holder. Carbon steel with a 4mm wall.
  • A bolt-down base plate with four bolt holes (150 × 105 × 5mm for the 90mm holder, 155 × 205 × 5mm for the 140mm).

Not in the price

  • The bollard. The holder is an accessory for the SW-RB90 or SW-RB140 removable bollard.
  • Masonry anchors or bolts. Fixings are not included.
  • An in-ground socket. That comes with each removable bollard, not with the holder.
  • Freight and GST. Freight is quoted per job; GST is added at 10%.

Construction

  • Carbon steel holder with a 4mm wall.
  • Bolt-down base plate fixes the holder flat to the floor surface.
  • Open top so the bollard drops straight in and lifts straight out.
  • Matched to bollard diameter: order the holder that suits your bollard size.

Fits with

See the removable bollards page for the matching bollard specs, or our 90mm vs 140mm guide if you're still deciding on size. Fitting the in-ground socket is covered in how to install removable bollards.

A holder only parks a bollard, so it goes with a removable bollard (from $120 ex GST, $132 inc GST, pre-order), which comes with its own in-ground socket. See removable bollards

Where they're used

Common applications

Factory & warehouse roller doors

Bollards marking off a roller door opening often need to come out for deliveries. Bolt a holder just inside the door so the bollards have a home while machinery moves through.

Garages & driveways

Lift the bollard out to bring the car in, drop it into a floor-bolted holder, and lock it back in position when you're done.

Loading docks

Bolt a holder near each removable position so bollards pulled for a delivery truck don't end up leaning against a wall or underfoot.

Car parks with removable bays

Where bays switch between reserved and open access, a holder keeps the spare bollard upright and out of the way between uses. Bollards mark the bay; they are not a vehicle barrier.

Events & council sites

Sites where delineation bollards come out and go back in often, such as event access points, laneways and shared paths, benefit from a fixed spot to store them.

Spare-bollard storage

Keep a holder on hand for spare or replacement bollards so they're never just propped against a wall or lying on the ground.

Installation

How they go in: the short version

Installation is simple surface fixing, with no digging or concrete work involved.

  1. Position it

    Choose a spot out of the way (against a wall inside a garage or factory door, or beside the bollard's ground position) and sit the holder in place.

  2. Mark & drill

    Mark the four bolt holes in the base plate, then drill into the concrete or masonry floor.

  3. Bolt down

    Fix the holder with masonry anchors or bolts suited to the floor. Fixings aren't included.

Installation is the responsibility of the purchaser or their contractor. SafeWise supplies product only.
Bollard storage holder bolted to a concrete floor

FAQs

Common questions

What is a bollard storage holder?

It's a bolt-down floor holder for a removable bollard. When you unlock and lift the bollard out of its in-ground socket, you drop it into the holder so it stands upright and secure instead of leaning against a wall or lying on the ground. It's an accessory for removable bollards only. It's not installed in the ground.

Is a bollard storage base the same as a bollard sleeve?

No. A storage base (also called a storage holder) is a bolt-down steel fitting that parks a removed bollard. A socket is the steel tube set in the ground that holds the bollard in use, and it is supplied with each removable bollard. Sleeve is a trade word used for either, which is why we spell out which one we mean.

Are bollard storage holders in stock?

Yes. Storage holders (SW-SL90 and SW-SL140) are in stock in Melbourne now. The removable bollards they park are on pre-order for our next container: factory production typically takes 15 to 20 days, plus sea freight and customs clearance.

How do I pay for storage holders?

Your written quote for storage holders sets out the price, freight and any payment terms that apply. Your order is confirmed only when you accept that quote.

Can I buy a storage holder without a bollard?

Yes. Holders are sold as a separate line item, so you can order extra holders for future bollard positions, or order holders now while bollards are on pre-order and put them to use once the bollards land.

Do I need a storage holder for every removable bollard?

Not necessarily. You need one holder for each bollard that is out at the same time. If four bollards are lifted out for a delivery, you need four holders; if only one is ever out at a time, one holder of the right size is enough.

Can I use a storage holder as an in-ground socket?

No. The storage holder is a bolt-down surface fitting that only parks a removed bollard. It is not an in-ground socket and is not designed to be set into concrete or to hold a bollard in place for use. Every removable bollard comes with its own in-ground socket and key lock, and that socket is what holds the bollard in the ground.

Need storage holders?

They're in stock in Melbourne. Send quantities and your postcode for a landed price, or add them to a bollard enquiry.

Request a quote